Upgraded a switch to 1.3.7 tonight/this morning and noticed that flow control is not showing as "on" on any of my Gigabit interfaces (e.g. backhauls).
What is used to determine if Flow Control shows up as "on"? it's definitely enabled on the ports tab, but the status tab doesn't show the two little arrows.
1.3.7 Now Flow Control on Gig Interfaces?
-
sirhc - Employee
- Posts: 7415
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
Re: 1.3.7 Now Flow Control on Gig Interfaces?
mhoppes wrote:Upgraded a switch to 1.3.7 tonight/this morning and noticed that flow control is not showing as "on" on any of my Gigabit interfaces (e.g. backhauls).
What is used to determine if Flow Control shows up as "on"? it's definitely enabled on the ports tab, but the status tab doesn't show the two little arrows.
This is a "known" issue with UBNT 1G devices, they are fixing this. "They" have it turned OFF on a lot of their newer devices.
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
-
mhoppes - Associate
- Posts: 664
- Joined: Thu Apr 10, 2014 9:14 pm
- Location: Pennsylvania
- Has thanked: 10 times
- Been thanked: 125 times
Re: 1.3.7 Now Flow Control on Gig Interfaces?
So then why would I have seen pause frames prior to upgrading the switch firmware?
-
sirhc - Employee
- Posts: 7415
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
Re: 1.3.7 Now Flow Control on Gig Interfaces?
mhoppes wrote:So then why would I have seen pause frames prior to upgrading the switch firmware?
I am just telling you some of UBNT 1G devices do not have Flow Control enabled.
For example the AF5X had flow control disabled and is just now enabled with newest RC version.
http://community.ubnt.com/t5/airFiber/F ... 085/page/2
Also most of their 1G airMAX radios have FC disabled.
What radio is this?
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
-
sirhc - Employee
- Posts: 7415
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
Re: 1.3.7 Now Flow Control on Gig Interfaces?
mhoppes wrote:airFiber24
What version firmware are you running on AF24 because if it is v3.X then that was discussed on the UBNT forum in the thread above and you were in that thread? Downgrade AF24 to v2X and it works
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
-
mhoppes - Associate
- Posts: 664
- Joined: Thu Apr 10, 2014 9:14 pm
- Location: Pennsylvania
- Has thanked: 10 times
- Been thanked: 125 times
Re: 1.3.7 Now Flow Control on Gig Interfaces?
I feel stupid. I started rooting around in the configuration and someone forgot to click "FC On" in the airFiber *sigh*.
-
sirhc - Employee
- Posts: 7415
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
Re: 1.3.7 Now Flow Control on Gig Interfaces?
mhoppes wrote:I feel stupid. I started rooting around in the configuration and someone forgot to click "FC On" in the airFiber *sigh*.
We all do stupid things, it happens but also note that v3X on AF24 FC is disabled [BUG in UBNT firmware], stick with v2X
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
-
mhoppes - Associate
- Posts: 664
- Joined: Thu Apr 10, 2014 9:14 pm
- Location: Pennsylvania
- Has thanked: 10 times
- Been thanked: 125 times
Re: 1.3.7 Now Flow Control on Gig Interfaces?
Thanks! I did know about that.
9 posts
Page 1 of 1
Who is online
Users browsing this forum: Google [Bot] and 37 guests