I have a question about the DC Wisp switch or tower switch when it arrives.
If I am going to power a AirFiber5 what input voltage and current is required to power the switch and the AirFiber radio?
Will the switch up convert a lower voltage to the 48 VDC required or will it only down convert to lower voltages?
DC WISP switch
-
sirhc - Employee
- Posts: 7419
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
Re: DC WISP switch
The DC WISP Switch does not care what input voltage it gets 9-60V it always outputs the voltages it is supposed to.
Yes it upconverts or downconverts on the fly, it is SMART.
Yes it upconverts or downconverts on the fly, it is SMART.
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
-
kbloch - Member
- Posts: 34
- Joined: Thu Sep 04, 2014 10:45 am
- Location: Western USA
- Has thanked: 1 time
- Been thanked: 6 times
Re: DC WISP switch
Good to hear how SMART the switch will be when it arrives.
We have an upcoming installation where a 100 meter run of CAT5/6 will not be long enough. The AirFiber will be closer to 400 feet with the path the conduit will be run. If we can install a DC Power WISP switch at around the half way mark then all should be good. Running DC power with the ethernet in the same conduit should not be problem like it would be if it was AC power.
We have an upcoming installation where a 100 meter run of CAT5/6 will not be long enough. The AirFiber will be closer to 400 feet with the path the conduit will be run. If we can install a DC Power WISP switch at around the half way mark then all should be good. Running DC power with the ethernet in the same conduit should not be problem like it would be if it was AC power.
-
sirhc - Employee
- Posts: 7419
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
Re: DC WISP switch
The lower the voltage the more heat that will be generated.
I would not put it up in the air 200 feet and feed it 12V.
What voltage are you planning to put on the wire and what gauge wire?
I would not put it up in the air 200 feet and feed it 12V.
What voltage are you planning to put on the wire and what gauge wire?
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
-
kbloch - Member
- Posts: 34
- Joined: Thu Sep 04, 2014 10:45 am
- Location: Western USA
- Has thanked: 1 time
- Been thanked: 6 times
Re: DC WISP switch
Power supply will be a 27.5 VDC. Actually it is two 27.5 VDC in the same rack mount unit running in parallel to redundancy. I can switch it to a 54 volt but would lose the redundancy. Output current is 20 AMP continuous and 25 AMP peak. Should be way more then needed to power a single AirFiber 5.
-
sirhc - Employee
- Posts: 7419
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
Re: DC WISP switch
That voltage is fine (27V) but the higher one would be better, you can play around once you get one
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
-
WisTech - Associate
- Posts: 213
- Joined: Mon Aug 04, 2014 3:57 pm
- Has thanked: 8 times
- Been thanked: 64 times
Re: DC WISP switch
I'd just like to know when I can get my hands on a few Christopher! *wink*
-
wayneorack - Experienced Member
- Posts: 129
- Joined: Thu Sep 04, 2014 12:16 pm
- Location: San Angelo, TX
- Has thanked: 188 times
- Been thanked: 64 times
Re: DC WISP switch
WisTech wrote:I'd just like to know when I can get my hands on a few Christopher! *wink*
Are you sure it is not: Rehpotsirhc ?
-
sirhc - Employee
- Posts: 7419
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
Re: DC WISP switch
mhoppes wrote:What happens if I feed it -48?
It all depends on how the facility dealt with chassis/rack grounding.
Was DC negative or positive bonded to chassis/racks and or earth ground.
Obviously one can switch the cables positive with negative to feed our switch +48V so it comes down to how everything else in the facility.
Look, our switches expect 48V not -48V so it is easy enough to flip the cables now you need make sure how the facility dealt with Earth Ground and what if and voltage/polarity (if any) is bound to the chassis/racks.
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Who is online
Users browsing this forum: No registered users and 22 guests