Compatible SFP Modules - FIRST POST IS COMPILED LIST

[sirhc]

Are there any updates on the MikroTik S-RJ01 modules working with Netonix switches? I'd really appreciate it if these would work since I can't source anything else from my distributor.
I happen to have ordered 4 of them because I went through this thread and read that someone had suggested them and stated that they were working. So is this a case-by-case issue?
NOT WORKING!


I need to know, which SFP -> RJ45 module works with the latest Netonix firmware and will continue to operate in the future?

TY.

1) What firmware version are you using on the switch?
2) Did you play with the Speed/Duplex settings on both sides of the link?

[Eric Stern]

Are there any updates on the MikroTik S-RJ01 modules working with Netonix switches? I'd really appreciate it if these would work since I can't source anything else from my distributor.
I happen to have ordered 4 of them because I went through this thread and read that someone had suggested them and stated that they were working. So is this a case-by-case issue?
NOT WORKING!


I need to know, which SFP -> RJ45 module works with the latest Netonix firmware and will continue to operate in the future?

TY.

Its in 1.4.5rc8.

viewtopic.php?f=17&t=2101

[jowang]

Have used the Cisco GLC-T modules from FS.COM, it works.

[StrataNet]

To throw in my 2 cents... I upgraded WS-12-250-AC switch from 1.4.3rc7 to 1.4.7rc11 today. Now MikroTik S-35LC20D appears to be working - running an RB260GS at the other end. Had to set both ends to 1G - not Auto.

[LRL]

Interesting to know I just ordered a bunch of Max wave SFP modules because of all the problems we were having with the mikrotik ones.

[tcknudson]

sfp converter, 10Gtek GLC-T for Cisco
RJ45 SFP works fine in Netonix switches,

for that time when you really need one more port and you have two empty fiber ports,

Available on Ebay for 19.00

[LRL]

There is something weird with SFP. I can get ONE GLC to work, but not TWO (one in each sfp). I have a few switches where two work just fine. But many more where I can't get two to work simultaneously. It seems like the board Rev is the only difference. On board REV E no problem with two, but on Rev D or REV B can only get one to work at a time. I can reboot and sometimes get the other port to work and then the one that was working stops. It's very odd.

All switches running 1.4.6

[sirhc]

Well I would upgrade to v1.4.7rc14 (just because that is the standard process to try the latest firmware first)

Then I would try with set to Auto for speed/duplex, then try setting to 1G but remember if you set one side of a link to 1G or Auto you need to match that setting on the other device on the the other side of the link.

If that failed I would try another brand but if that failed then it would be RMA time.

[CuninganReset]

Hello.

TP-Link TL-SM311LSworking great.

Single mode Gigabit F.O. SFP

[Julian]

So, I ran through the SFP reports thread and compiled a list of reports on specific model numbers. Grouped solely by functionality, and in alphabetical order, with no further guarantee:


WORKS:
10Gtek GLC-T
10Gtek SFP-T
Addon SFP-SX
Avago AFCT-5765ATPZ
Avago AFCT-5717APZ
Ciena XCVR-A10Y31
CISCO DS-SFP-FC-2G-SW
Cisco GLC-LH-SM
CISCO GLC-SX-MM
CISCO GLC-ZX-SM
Cisco SFP-H10GB-CU5M

EB-Link J4858A/B/C
Fiberstore SFP-1GTA-1M
Fiberstore SFP-GE-BX
Fiberstore SFP-GB-GE-T
Fiberstore SFP-10G-DAC (.5m)
Finisar FTRJ8519P1BNL-J2
Finisar FTLF9519P2BNL
Gencom GLC-BX-U
Gencom GLC-BX-D
GLC-SX-MM
GLC-ZX-SM
GLS-SX-MMD-A0
HP J4858B
HP J4858C
LongLine GLC-T-LL
Maxwave MW-1513-SM-US
Maxwave MW-1315-SM-US
Maxwave MW-LX-SM-US
Maxwave MW-SX-MM-US
Mikrotik S-3553LC20D
Mikrotik S+DA0001r2
Mikrotik S-31DLC20D
Mikrotik S-85DLC05D
Mikrotik S-35LC20D
Mikrotik S-53LC20D
NCOM GLC-T
Netgear AGM732F-R
Planet MGB-TLX
Proline Generic HP SFP J4859C-CDW
ROBOfiber SFP-7000-85
SFP-LX-1
Telecoast GLC-BX-D-20-TC
TP-Link TL-SM311LS
Ubiquiti UF-MM-1G


SORTA WORKS:
Cisco CAB-SFP-50CM - Netonix to Netonix interconnection works, Cisco to Cisco interconnection works, Netonix to Cisco not so much

Fiberstore BLSFP-1G53-20-CO (disable FC while module inserted, starts working, if reseated, won't initialize)
Fiberstore BLSFP-1G35-20-CO (disable FC while module inserted, starts working, if reseated, won't initialize)
GLC-T-OEM (requires reseating after rebooting)
GLC-T-LU (not sure, thing stopped working entirely, pretty sure I broke it)
Mikrotik S-RJ01 (does not work with all models?)
Mikrotik S-85DLC05D (conflicting reports)
SFP TL-SM321A/B (connection works, UI shows false no link)


DOESN'T WORK (confirmed):
Alcatel Lucent 3FE
Finisar FTLF1318P3BTL
Level One SFP-3211
NCOM GLT-T (works a couple hours, then quits)
OEM GLC-BX-U-00
OEM GLC-BX-D-00
Oersen SA1
RB-FTC-11
Volex VAHS-28-0029
Mikrotik S+DA0001 (early revision)
Ubiquiti UF-SM-1G-S