Page 1 of 1
MAC table not showing up
Posted: Sun Oct 18, 2015 2:29 pm
by highlands
I can not seem to get the MAC table to show. When testing it on the bench it was there (all 8 MACs) but there none the less. Now that they are in production and I wanted to track down a MAC I am unable to get it to display. I read in another post it was sometime (with older firm ware) taking 140 seconds to display I have waited a hour with no joy.
Any suggestions?
An estimated 1100 MAC should display.
Firmware Version
1.3.4
Board Rev
D
John
Re: MAC table not showing up
Posted: Wed Oct 21, 2015 1:55 am
by highlands
I can not seem to get the MAC table to show. When testing it on the bench it was there (all 8 MACs) but there none the less. Now that they are in production and I wanted to track down a MAC I am unable to get it to display. I read in another post it was sometime (with older firm ware) taking 140 seconds to display I have waited a hour with no joy.
Any suggestions?
An estimated 1100 MAC should display.
Firmware Version 1.3.4
Board Rev D
John
Updating the information;
json_object_from_file: error reading file ../tmp/mactable.json: No such file or directory
Segmentation fault
Netonix Switch# show mac table
Segmentation fault
MAC Port VLAN Manufacturer Last IP
----------------- ---- ---- ------------ ---------------
json_object_from_file: error reading file ../tmp/mactable.json: No such file or directory
Re: MAC table not showing up
Posted: Wed Oct 21, 2015 9:34 am
by sirhc
This was reported earlier, it is on our list to look at later today as we are finishing up v1.3.5
It has to do with large number of MACs as now both people reporting this have 800+ MACs
Re: MAC table not showing up
Posted: Wed Oct 21, 2015 2:38 pm
by highlands
So the bug would be there even if I rolled back to 1.3.3?
John
Re: MAC table not showing up
Posted: Wed Oct 21, 2015 2:50 pm
by sirhc
highlands wrote:So the bug would be there even if I rolled back to 1.3.3?
John
Rolling back will not fix it
This is fixed in v1.3.5 or so I am told, I do not have a large flat network to test so the most MACs I have on one tower is less than 300
We hope to roll out v1.3.5 maybe tonight or at the latest unless something goes terribly wrong tomorrow night
Re: MAC table not showing up
Posted: Wed Oct 21, 2015 3:53 pm
by sirhc
Was just talking to the crew, looks like v1.3.5 will be released late tomorrow night
Re: MAC table not showing up
Posted: Fri Oct 23, 2015 1:19 am
by highlands
That's a fast turnaround for firmware! One feature I would like to have is the "test" function. That one feature has save sooooo many trips to the sites. I do look forward to you getting that one as I have locked myself out of the Netonix a few times.
John
Re: MAC table not showing up
Posted: Fri Oct 23, 2015 8:56 am
by sirhc
highlands wrote:That's a fast turnaround for firmware! One feature I would like to have is the "test" function. That one feature has save sooooo many trips to the sites. I do look forward to you getting that one as I have locked myself out of the Netonix a few times.
John
We are getting down to the wire on v1.3.5 so soooon!
Re: MAC table not showing up
Posted: Fri Oct 23, 2015 9:46 am
by lligetfa
sirhc wrote:... soooon!
Not to be confused with the Ubiquiti trademarked Soon (with fewer o's).
Re: MAC table not showing up
Posted: Fri Oct 23, 2015 9:49 am
by sirhc
lligetfa wrote:sirhc wrote:... soooon!
Not to be confused with the Ubiquiti trademarked Soon (with fewer o's).
LOL - Well as long as you do not include our CAP then sooon has always been measured in hours, days, and a few times weeks.
Now the CAP is over a year so our soon on that sucked too.
But soon on this occasion should be hours or days - LOL