Received a pair of B5 integrated units yesterday and the first thing I wanted to know was if the WISP Switch would power them... ... well, it wont.
The power supply that comes with the B5's are 56v .9 amp (50.4 watts) but the specs on the mimosa website (http://mimosa.co/home/Products/Backhaul ... tions.html) say each unit only draws 20 watts max. They also mention they are 802.3at and passive poe complaint at 48-56 volts. However my units would not power up on a 48VH port..
I did swap patch cables but I didn't try a different port just to be sure something wasn't already wrong. The unit works fine on the supplied power supplies. Next time I am at the office I will test another port.. but so far I'm disappointed.
Mimosa B5
-
sirhc - Employee
- Posts: 7416
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
Re: Mimosa B5
Post up the pin out
if it is 802.3at then 48VH port should work fine if pin outs are the same which it should be (reference our PDF)
CLICK IMAGE TO SEE FULL SIZE
if it is 802.3at then 48VH port should work fine if pin outs are the same which it should be (reference our PDF)
CLICK IMAGE TO SEE FULL SIZE
- POE.png (183.06 KiB) Viewed 19403 times
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
-
adairw - Associate
- Posts: 465
- Joined: Wed Nov 05, 2014 11:47 pm
- Location: Amarillo, TX
- Has thanked: 98 times
- Been thanked: 132 times
Re: Mimosa B5
I'm pretty sure that I checked and it was the same. now I can't find the pinout. I'll keep looking.
-
adairw - Associate
- Posts: 465
- Joined: Wed Nov 05, 2014 11:47 pm
- Location: Amarillo, TX
- Has thanked: 98 times
- Been thanked: 132 times
Re: Mimosa B5
http://help.mimosa.co/backhaul-faq-volt ... ifications
http://help.mimosa.co/backhaul-faq-non-mimosa-poe
If the WS support 802.3at it should work.. I can't find anything on the mimosa website that shows the actual pins used. but your diagram looks like like any other standard 802.3at pin out. hmm..
http://help.mimosa.co/backhaul-faq-non-mimosa-poe
If the WS support 802.3at it should work.. I can't find anything on the mimosa website that shows the actual pins used. but your diagram looks like like any other standard 802.3at pin out. hmm..
-
sirhc - Employee
- Posts: 7416
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
Re: Mimosa B5
One thing you can do is make a jumper with bare wires on one end and use a Volt Ohm Meter to test the pin out of the MIMOSA power brick.
Be careful not to short any wires as it could damage the brick and or the switch if you do also test the switch.
Dumb question but you are using one of the following ports?
48VH configured in UI using one of the following WISP Switch ports:
WS-12-250A or WS-24-400A ports 1, 2, 3 or 4
WS-12-250B or WS-24-400B ports 1 or 2
Be careful not to short any wires as it could damage the brick and or the switch if you do also test the switch.
Dumb question but you are using one of the following ports?
48VH configured in UI using one of the following WISP Switch ports:
WS-12-250A or WS-24-400A ports 1, 2, 3 or 4
WS-12-250B or WS-24-400B ports 1 or 2
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
-
adairw - Associate
- Posts: 465
- Joined: Wed Nov 05, 2014 11:47 pm
- Location: Amarillo, TX
- Has thanked: 98 times
- Been thanked: 132 times
Re: Mimosa B5
Yep. I was using port 2 on a WS-24-400A. It has a red blinking LED showing the 48VH is active.
I'll head up the the data center later today and try another port and see about doing some additional testing.
I'll head up the the data center later today and try another port and see about doing some additional testing.
-
Dave - Employee
- Posts: 726
- Joined: Tue Apr 08, 2014 6:28 pm
- Has thanked: 1 time
- Been thanked: 158 times
Re: Mimosa B5
Maybe it has pin out power info on the back of the adapter it came with...
-
lee - Member
- Posts: 5
- Joined: Sun Dec 21, 2014 3:32 pm
- Location: Campbell, CA
- Has thanked: 0 time
- Been thanked: 3 times
Re: Mimosa B5
Lee Peterson from Mimosa here. Would be interested in understanding why the B5 is having a problem the WISP switch. The radio will work with any 802.3at 48v POE. The additional voltage (56v) in our POE power supply is to account for voltage drops on long cable runs.
-
adairw - Associate
- Posts: 465
- Joined: Wed Nov 05, 2014 11:47 pm
- Location: Amarillo, TX
- Has thanked: 98 times
- Been thanked: 132 times
Re: Mimosa B5
Hi Lee. Me too!
I'm going to do some testing this afternoon and will report my findings.
Having a brand new ws 24 I've never had anything plugged in to port 2. So while I hope the port isn't bad... Something isn't lining up.
I'm going to do some testing this afternoon and will report my findings.
Having a brand new ws 24 I've never had anything plugged in to port 2. So while I hope the port isn't bad... Something isn't lining up.
Who is online
Users browsing this forum: No registered users and 7 guests