Upgraded no problem, but lost communication to and through two of my AP's plugged into ports 8 and 9 on two separate VLANs. Reverted back to rc5 and still nothing. Disabled vlan, re-enabled, deleted and added, still nothing. Bounced the ports and the units reboot as normal, just no pings or communication through the ports as if the VLAN config is trashed.
A little help?
Upgrade to 1.0.10rc6 Failure
-
sirhc - Employee
- Posts: 7490
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1643 times
- Been thanked: 1336 times
Re: Upgrade to 1.0.10rc6 Failure
Not sure, I upgraded my WISP switches with no issues?
There was literally no other changes done to the firmware from v1.0.10rc5 other than how it reacts on a reboot after power failure - COLD BOOT?
There was literally no other changes done to the firmware from v1.0.10rc5 other than how it reacts on a reboot after power failure - COLD BOOT?
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
-
WisTech - Associate
- Posts: 213
- Joined: Mon Aug 04, 2014 3:57 pm
- Has thanked: 9 times
- Been thanked: 64 times
Re: Upgrade to 1.0.10rc6 Failure
I'm looking at the MAC table and showing multiple VLAN's across different VLAN ports, I have 2 problematic radios (ports), the others are fine.
-
sirhc - Employee
- Posts: 7490
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1643 times
- Been thanked: 1336 times
Re: Upgrade to 1.0.10rc6 Failure
If your switch is easily accessed I would upgraded it back to v1.0.10rc6 then power cycle it (COLD BOOT).
We should probably put an option in the UI to preform a "COLD REBOOT" which will unfortunately bounce the POE ports but may from time to time be needed/useful as embedded devices are really no different than computers in that sometimes they just need a COLD REBOOT or power cycle to fix something squirrely?.
I am really sorry for your troubles on New Years Eve, my bad!
We should probably put an option in the UI to preform a "COLD REBOOT" which will unfortunately bounce the POE ports but may from time to time be needed/useful as embedded devices are really no different than computers in that sometimes they just need a COLD REBOOT or power cycle to fix something squirrely?.
I am really sorry for your troubles on New Years Eve, my bad!
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
-
WisTech - Associate
- Posts: 213
- Joined: Mon Aug 04, 2014 3:57 pm
- Has thanked: 9 times
- Been thanked: 64 times
Re: Upgrade to 1.0.10rc6 Failure
Chris - An actual reboot (after firmware upgrade) resolved it temporarily, then ports 8,9 and 11 are all crossed up. The other ports operate fine and are isolated. Guess I'll take the spare 24 and take a drive.
Will let you know. Thanks man. What sucks more is whiny customers.
Will let you know. Thanks man. What sucks more is whiny customers.
-
WisTech - Associate
- Posts: 213
- Joined: Mon Aug 04, 2014 3:57 pm
- Has thanked: 9 times
- Been thanked: 64 times
Re: Upgrade to 1.0.10rc6 Failure
Chris - I disabled the VLANs on both of the problematic ports, rebooted (remotely), then enabled one and applied, everything came back up normally... waited, then enabled the other port. Everything still seems to be functioning normally. I'll keep an eye on it and report back.
Thanks for your help.
PS - I'm still on RC5, dad's shitting a brick because I did it during business hours.
Tony
Thanks for your help.
PS - I'm still on RC5, dad's shitting a brick because I did it during business hours.
Tony
Last edited by WisTech on Wed Dec 31, 2014 7:11 pm, edited 1 time in total.
-
sirhc - Employee
- Posts: 7490
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1643 times
- Been thanked: 1336 times
Re: Upgrade to 1.0.10rc6 Failure
I am really sorry Tony but yes keep me posted, I am staying home tonight and working.
My guess is your unit got confused and really could use a cold reboot, it happens sadly.
My guess is your unit got confused and really could use a cold reboot, it happens sadly.
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
7 posts
Page 1 of 1
Who is online
Users browsing this forum: Google [Bot] and 20 guests